TVS Apache RTR 160 Speedometer Cable Price - Replacement Cost

The speedometer cable on the TVS Apache RTR 160 is responsible for transmitting rotational motion from the front wheel to the speedometer head. When this cable breaks or wears out, your speedometer stops working entirely. This guide covers the TVS Apache RTR 160 speedometer cable price, how to identify a faulty cable, and step-by-step replacement instructions.

Apache RTR 160 Speedometer Cable Price

The cost of a replacement speedometer cable for the Apache RTR 160 varies depending on the source. Here are the typical price ranges:

  • OEM TVS Genuine Cable: INR 150 to INR 350. Original TVS cables are available at authorized service centers. The part number is typically G5130110 or a similar variant depending on the model year.
  • Aftermarket Cable: INR 80 to INR 200. Aftermarket cables from brands like Zana, Roots, and local manufacturers are widely available. They are generally compatible but may have slightly different lengths or fitting quality.
  • Online Marketplaces: INR 120 to INR 300. Amazon, Flipkart, and specialized motorcycle parts websites stock cables for the Apache RTR 160. Check reviews before purchasing.

The price is low enough that you should always replace a faulty cable immediately. If you suspect the cable is not the only problem, verify your speed using our GPS speedometer tool to check if the speedometer head itself is receiving any signal.

Symptoms of a Faulty Speedometer Cable

Recognizing the signs of a failing speedometer cable helps you diagnose the problem before you start buying parts. Look for these telltale signs:

  • Speedometer shows zero: The most obvious symptom. The needle stays at zero regardless of speed.
  • Erratic needle movement: The needle jumps, bounces, or fluctuates wildly. This often indicates that the cable is about to break completely.
  • Whining or squeaking noise: A dry or binding cable produces a high-pitched noise from the front wheel area. This noise changes with speed.
  • Odometer stops working: Since the odometer is driven by the same cable, it too will stop counting kilometers.
  • Visible cable damage: Inspect the cable at the wheel end. A frayed inner wire or cracked outer housing confirms the problem.

How to Replace the Speedometer Cable

Replacing the speedometer cable on an Apache RTR 160 is a simple task that requires basic tools. Here is the procedure:

  1. Raise the front of the motorcycle using a center stand or paddock stand so the front wheel is off the ground.
  2. Locate the cable connection at the front wheel hub. It is on the left side of the wheel, where the cable enters the speedometer drive gear housing.
  3. Unscrew the knurled nut that holds the cable to the drive gear housing. Pull the cable out.
  4. Follow the cable up to the speedometer head. Remove any cable clips or zip ties holding it in place along the fork leg.
  5. Unscrew the cable from the back of the speedometer head. Older RTR 160 models have a knurled nut, while newer ones may use a screw-on cap.
  6. Pull the old cable out completely. Note the routing path so you can replicate it with the new cable.
  7. Install the new cable by feeding it through the same routing path. Ensure there are no sharp bends.
  8. Connect the cable to the speedometer head first, then to the wheel drive unit. Tighten both connections firmly but do not overtighten.
  9. Secure the cable with the original clips or new zip ties.
  10. Take a test ride and verify the speedometer works correctly. Use a GPS speedometer to confirm accuracy.

OEM vs Aftermarket Cable

OEM TVS cables are recommended for their precise length and high-quality inner wire. They are pre-greased and ready to install. Aftermarket cables can be hit or miss. Some have poorly fitting ends that cause them to come loose, while others use thinner inner wires that break sooner. If you are not experienced with motorcycle maintenance, paying a little extra for the OEM cable is worth the peace of mind.

Preventive Maintenance

Speedometer cables last longer with proper care. Every 10,000 kilometers, disconnect the cable from the speedometer head and apply a small amount of lithium grease to the inner wire. This prevents the cable from drying out and snapping. Also, check that the cable is routed without sharp kinks or contact with the exhaust pipe, which can melt the outer housing.